m开头的手机网站怎么做,手工制作大全视频教程,做百度手机网站优化快,个人中心登录注册1开启时钟 2开启定时器和通道设置为PWM模式 3将定时时间设置为50Hz(20ms)//每25为1ms 4代码编写
4.1开启PWM
4.2改PWM的占空比
4.3效果0~180度在0度
源码
/* USER CODE BEGIN Header */
/******************************************************************************…1开启时钟 2开启定时器和通道设置为PWM模式 3将定时时间设置为50Hz(20ms)//每25为1ms 4代码编写
4.1开启PWM
4.2改PWM的占空比
4.3效果0~180度在0度
源码
/* USER CODE BEGIN Header */
/********************************************************************************* file : main.c* brief : Main program body******************************************************************************* attention** Copyright (c) 2024 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************/
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include main.h
#include tim.h
#include gpio.h/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes *//* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD *//* USER CODE END PTD *//* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD *//* USER CODE END PD *//* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM *//* USER CODE END PM *//* Private variables ---------------------------------------------------------*//* USER CODE BEGIN PV *//* USER CODE END PV *//* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
/* USER CODE BEGIN PFP *//* USER CODE END PFP *//* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 *//* USER CODE END 0 *//*** brief The application entry point.* retval int*/
int main(void)
{/* USER CODE BEGIN 1 *//* USER CODE END 1 *//* MCU Configuration--------------------------------------------------------*//* Reset of all peripherals, Initializes the Flash interface and the Systick. */HAL_Init();/* USER CODE BEGIN Init *//* USER CODE END Init *//* Configure the system clock */SystemClock_Config();/* USER CODE BEGIN SysInit *//* USER CODE END SysInit *//* Initialize all configured peripherals */MX_GPIO_Init();MX_TIM2_Init();/* USER CODE BEGIN 2 */HAL_TIM_PWM_Start(htim2,TIM_CHANNEL_1);int b0;/* USER CODE END 2 *//* Infinite loop *//* USER CODE BEGIN WHILE */while (1){bb10;__HAL_TIM_SET_COMPARE(htim2,TIM_CHANNEL_1,b);if(b200){b0;}HAL_Delay(500);//HAL_Delay(1000);/* USER CODE END WHILE *//* USER CODE BEGIN 3 */}/* USER CODE END 3 */
}/*** brief System Clock Configuration* retval None*/
void SystemClock_Config(void)
{RCC_OscInitTypeDef RCC_OscInitStruct {0};RCC_ClkInitTypeDef RCC_ClkInitStruct {0};/** Initializes the RCC Oscillators according to the specified parameters* in the RCC_OscInitTypeDef structure.*/RCC_OscInitStruct.OscillatorType RCC_OSCILLATORTYPE_HSE;RCC_OscInitStruct.HSEState RCC_HSE_ON;RCC_OscInitStruct.HSEPredivValue RCC_HSE_PREDIV_DIV1;RCC_OscInitStruct.HSIState RCC_HSI_ON;RCC_OscInitStruct.PLL.PLLState RCC_PLL_ON;RCC_OscInitStruct.PLL.PLLSource RCC_PLLSOURCE_HSE;RCC_OscInitStruct.PLL.PLLMUL RCC_PLL_MUL9;if (HAL_RCC_OscConfig(RCC_OscInitStruct) ! HAL_OK){Error_Handler();}/** Initializes the CPU, AHB and APB buses clocks*/RCC_ClkInitStruct.ClockType RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;RCC_ClkInitStruct.SYSCLKSource RCC_SYSCLKSOURCE_PLLCLK;RCC_ClkInitStruct.AHBCLKDivider RCC_SYSCLK_DIV1;RCC_ClkInitStruct.APB1CLKDivider RCC_HCLK_DIV2;RCC_ClkInitStruct.APB2CLKDivider RCC_HCLK_DIV1;if (HAL_RCC_ClockConfig(RCC_ClkInitStruct, FLASH_LATENCY_2) ! HAL_OK){Error_Handler();}
}/* USER CODE BEGIN 4 *//* USER CODE END 4 *//*** brief This function is executed in case of error occurrence.* retval None*/
void Error_Handler(void)
{/* USER CODE BEGIN Error_Handler_Debug *//* User can add his own implementation to report the HAL error return state */__disable_irq();while (1){}/* USER CODE END Error_Handler_Debug */
}#ifdef USE_FULL_ASSERT
/*** brief Reports the name of the source file and the source line number* where the assert_param error has occurred.* param file: pointer to the source file name* param line: assert_param error line source number* retval None*/
void assert_failed(uint8_t *file, uint32_t line)
{/* USER CODE BEGIN 6 *//* User can add his own implementation to report the file name and line number,ex: printf(Wrong parameters value: file %s on line %d\r\n, file, line) *//* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */
